Showing posts with label Harlem Globetrotters Pinball. Show all posts
Showing posts with label Harlem Globetrotters Pinball. Show all posts

Wednesday, March 21, 2018

Rebuilding a pinball flipper

On the Harlem Globetrotters pinball machine, only two of the three flippers were working and they seemed sluggish. It was time to rebuild them!



Step 1 was to get it off the table. I unscrewed the plate everything was on and tried to remove it. No luck. It was connected to the flipper on the other side. I thought I would just pry the flipper off, no luck.

Finally after some head scratching I noticed the hex pins on the side of the shaft. It took awhile to locate the proper sized hex tool, but eventually I was able to loosen it.




Once it was removed I was able to take the whole unit apart.


Into the tumbler all of the parts went for an overnight cleaning and polishing.The plunger itself was sanded with 1000 grit sandpaper and then polished with some polish so it would slide through the solenoid with ease.

After a night of tumbling and cleaning everything out, it was time to put it all back together. I don't have too many pictures, but I do have a nice little 15 second video of the flipper in action. Check out the action on this thing!

Woohoo, now to do the other two!


Tuesday, March 13, 2018

And..... its alive!

The Harlem Globetrotters table is alive!

After all this time, the lights come on and the solenoids move and the sounds beep. Its amazing.

When I got it  back in 2015 ( link ) I never thought it would take this long. Part of it was my limited skills, and part was I seriously underestimated how much work was needed. I opened it up and it looked pretty clean so I thought it was a minor problem and I would be good.

live and learn.

But now after replacing a fuse that looked good but intermittantly did not make contact, its all in good shape.

I could actually try and play a game on it but the next step is to figure out what is wrong with the front door and the "start a game" switch which currently does nothing.


Wednesday, March 7, 2018

A gigantic step forward

Finally, finally, I have made progress with the Harlem Globetrotters pinball!

and this isn't a little progress, this is a LOT of progress!

I started working on the unit, checking and identifying cables and connectors. I thought perhaps I had plugged the wrong one in and accidentally swapped a couple. So I sat down with the schematic and verified cables and wires (J2 is a 28 pin connector, wire 1 is green with grey stripe: check) and marked them with Sharpie.

I dug around and found a 2-wire connector that was supposed to go to the sound board that had not been connected and plugged it in.

When I was finished I turned it on. Lo and Behold I heard a sound!! yes, the startup music played and most of the lights started flashing:
it works!




According to the manual, self-test #5 was the sound self test, so I pushed the test button.

And some lights came on, not all of them but some changed and this was the light test!

With baited breath I pushed the test button again. The second test was the score displays. These had never shown anything in the 18 months I have had the unit. They all came on and counted up!

Seriously - this thin has been dead for 18 months while I slowly worked it over and now it has at least partially come to life!

Test 3 was the solenoid test and as usual, the only solenoid that works is the "match" solenoid. None of the playfield ones do anything.

Test 4 was the switch test, it shows a zero on the displa, not sure what that means yet

Test 5 was the sound test, it makes a continuous changing sound so I think its ok.

Theoretically I should be able to start a new game. The MPU board is set for free-play.

But when I push the "Start Game" button, nothing happens. No spark of electricity, nothing.

Looking at the coin-door unit shows it to be in pretty bad shape:
coin door

so its possible I am unable to start a game because the door wiring is screwed up...



Back to the schematic, but hey.....its alive!!!!!

Saturday, February 10, 2018

bad flipper switch

While looking at the burned out ball drain coil, I also looked at the flipper switches.

The left switch was in bad shape. It was all rusty and although I didn't get a very good picture, the contacts were touching even without the flipper button being pushed! that would be a real problem!

It was also off-center a little. So I pulled the rusty metal off and used a flapwheel sander on it which got rid of the rust quite nicely. 

I then used the dremel with wire brush to clean the contacts and finally needlenose pliers to bend it out a smidge. After some repeated banging around just to test, I think I have it set up correctly.



A problem I didn't even know I had! one more thing to check when working on pinball machines.

Ball drain coil repairs

on the Harlem globetrotter table the new MP3 board isn't resetting all the way. Of course there is no information with it such as what it means when it stops after only 4 blinks  of 6.

My guess is I have a bad coil or two, so let's take a look at them and see.

The most obvious starting point is the ball drain coil. Just looking at it, it looks like the paper cover is crispy, a sure sign it has over heated.

Checking the resistance on it confirms. it is only a few tenths of an ohm, basically a direct short.

After removing it I can also confirm that it's toasty, I am unable to move the plunger at all, a sure sign it has heated up and expanded inside.


I pulled it apart and set about the clean it.



Some soap and water later, it wasn't too bad but still had a lot of gunk on it, so I set to it with  some sandpaper. Finally I had it decently clean.




'The plunger was pretty crappy, and it needed to be smooth for easy moving, so I sanded it down and put some metal polish on it, it looks pretty good!

Now to get a replacement coil and put it all back together. One down and who knows how many to go.

Wednesday, February 7, 2018

Harlem Globetrotters pinball power trouble

The power troubles for the Harlem Globetrotter on Tour pinball machine appear to be solved!

After connecting the boards up, the test point on the board was showing low voltage. I was looking at having to pull components of the circuit board to try and solve the issue but after reading about Nic's "swab-polish-swab" technique where he wipes with alcohol, then polishes with a dremel and wire brush and then a final alcohol wipe - I decided to try it on the connectors. 

It solved the problem! Although they looked perfectly ok to me and I had seated and unseated the connectors many times, this time it seems to have fixed it and I was getting the correct voltage.

I plugged all the boards in, including my new MPU board and turned it on with great anticipation.

The lights came on, but the MPU board would not go through its self-test successfully. I could hear a coil pop and then it looks like it froze.

My guess is that I have a bad coil and its causing the new power board to pop its internal breaker.

Tme to start testing coils!

Friday, January 19, 2018

Power Trouble

Well, I didn't get the table up by New Years as I had hoped. I plugged everything in and started checking voltages.

According to the manual that came with the CPU board, do NOT plug it in unless the voltage at TP1 is 4.9-5.2 volts

Mine shows at 6.30 volts....sigh...and this is with a BRAND NEW voltage regulator board.
.
.
more posting to the forums
.
.
I get the reply back - "You should check this measurement at TP1 of the solenoid driver board, not the rectifier board."

Nice of them to provide 2 test points with the same name...sigh

Unfortunately, plugging the multi-meter in to the correct spot didn't work either...

As I suspected, I would need to replace the big Capacitor on the solenoid driver board...stay tuned!

Wednesday, December 13, 2017

update

I haven't posted much. Been busy with binging Netflix and my wife and I getting back into World of Warcraft. 

It is a lot of fun to quest together.

But the holidays are coming up and I have some time off, my goal is to get the Globetrotters table up and running by New Years.. wish me luck!

Saturday, October 14, 2017

installation

Now that the Hot Tip is working again, I have started work on re-assembling the Harlem Globetrotters pinball table back box.

After getting it all painted up, the next step was to get the shell pieces back installed.

Its amazing, how I am able to miss important pieces when photographing the old set up. I took over 40 pictures of the old shell as I took out the boards, mounting brackets and metal sheets, and I never got one picture that showed if two pieces were supposed to connect or not.

oh well, I am doing my best on this and should soon be able to turn it back on and see if it works!!!

Sunday, October 8, 2017

Harlem Globetrotters Soldering

Now that the box for the Harlem Globetrotters pinball table is painted and looks good, I am starting to put everything back together.

As you may recall I pulled everything out of the header ( link ) and painted it.

Time to put it all back in. As I re-assembled the light-panel (The wood with the lights on it) I noticed one of the LED displays had what appears to be burned out resistors on its little board:
Burned out resistors
Another soldering disaster! 

While I was able to get the resistors out of the board, I managed to deconnect the tiny traces and ring that the solder is supposed to connect to - why is my soldering so bad???

I spent all evening soldering them back in, using a meter to verify I have connectivity but I have no way to test them until I get it all put back together.

Looking at my soldering iron, I am going to try and lower the temperature on it. I have it set all the way up,  under the theory that hotter means faster but it could be its just too hot and is screwing things up. We will see if that helps.

In the meantime the Harlem Globetrotter table awaits reassembly as somehow I managed to lose one of the back pieces of sheet metal. Not a big deal but it means a wait until I can go back to the store for more.

Monday, August 28, 2017

Learning spray-painting the hard way

After my first attempt at spray painting, I opted for a much larger gun.  Specifically the 47016 gun.  According to the web page it:

  • Sprays enamels, lacquers, metallic, and urethanes
  • High versatility for automotive and hobby projects
  • Ideal for spraying base coats and primers
Sure sounded ideal. So I picked it up along with my can of Killz Primer.

The Killz website says I can spray at 2,500 psi to 3,000 psi which is far more than my air compressor can deliver.

The spray gun said it was supposed to run at 50 psi, so I set the compressor output at 50 and gave it a try. At first it seemed to work, then soon I got blobs of paint on the tip and the end result of all of this was total crap. The carefully smoothed surface became a mess of blobs and mottled paint:


I obviously need a LOT more experience in painting, but I don't have time to experiment on the cabinet. I want to get it working!

Out came the rattle-can

Wednesday, August 16, 2017

preparing the Harlem Globetrotters Pinball cabinet

After finishing up the Steampunk-Inspired lamp, I have turned my attention back to the Pinball tables. Specifically, getting the Harlem Globetrotters table topper fixed up. 

While the topper wasn't in terrible shape, there were bad edges, dents, the paint was faded and the box was covered in lead-based paint. So it definitely needed some work.

Plus this was a chance to learn a couple of things:
  1. how to do wood repair - specifically how to use Bondo (which is the recommended filler from a lot of repair gurus)
  2. How to spray paint. I have never used a spray gun - I have always used rattle cans (or a roller) for painting.
 I purchased some Bondo-brand filler at the hardware store, mixed it up and tried it out on some bad corners:

After gagging from the smell! I learned two key pieces of information:
  1. Bondo sets up quickly! I was only halfway through my pile of goop when it started hardening and would not spread easily on the wood.
  2. A thin coat is all you need! I laid it on thick, thinking it was like the stuff you put on sheetrock - easily sanded off - hah! I had to sand for hours to get rid of the big ridges and blobs I left all over the wood...sigh


But at last I had it good enough for a first coat of primer.

I pulled out my handy-dandy portable spray booth, set it up in the garage, loaded the top in it:



Got out the 3/4 Oz. Quick-Change Airbrush Kit I purchased:
and started in!

I quickly discovered that the 3/4 Oz. airbrush was far far too small for this use.  It is probable that I cannot get it adjusted to its maxiumum abilities but it is not even close. At its best, all I could produce was a light paint spray about 1 inch wide.

The good news was I was able to learn a bit about using a spray gun, the bad news was I need to purchase one 2 or 3 times this size.
 

Thursday, June 15, 2017

Cleaning the Pinball Wiring

With all the postings about my Steampunk-inspired lamp, it is hard not to forget that I am still working on the renovation of my Harlem Globetrotters World Tour pinball.

One of the key pieces is getting the wiring cleaned. It sounds simple to clean a wire but in reality you've got a large bundle of wires in poor, oily, dirty condition and it can be a lot of work to clean them.

After reading of several different techniques, I opted for Vid1900's guide. He basically says to throw it in the dishwasher, it will be fine!


Wiring harness in the dishwasher
So it was with considerable trepidation that I put my precious wiring into the dishwasher, worried about the colors on the wires (what if they all come out white!) worried about the connectors (what if the old plastic softens and the connectors fall out) worried about the moisture (what if water gets under the insulation and rusts the wires)

Per the recommendation, I put it on "High Temp Pots and Pans" rather than "gentle," crossed my fingers and pushed "Start"


90 minutes later I had a perfectly clean wiring harness!
Cleaned wiring

it looks like everything worked perfectly. My blue tape with labels on it even survived. 

I fired up the air compressor and blew out the moisture still trapped in the connectors just in case. But it all looks good!

whew



Tuesday, May 23, 2017

Globetrotters wooden box restoration - phase 2

Primary Sanding is complete. The majority of the (probable) lead-based paint has been removed and I can move one with detailed sanding and application of the first coat of filler and primer!

Wednesday, April 26, 2017

Globetrotters wooden box restoration - phase 1

Now that my computer table is finished (at least phase 1 of it) it is time to turn my attention to getting the Harlem Globetrotters pinball table working again.

As you have read from previous posts here and here, I have started with the back box. The actual wood box is in fairly poor shape, with damaged edges. But at least it is repairable without too much work - some glue and clamping and I should be back in business.

The paintwork is a different story. It is quite bad, faded out and should be redone. 
The old case


Some people like the original paint and want to preserve it at all costs, I prefer a more usability approach. I am taking it down to bare wood and repainting and redoing the graphics. When I am done it should look like new!

Taking it down to bare wood should be easy - sand or heat-gun the old paint off and get on with life. However, since the table is from the late 1970's it is still possible it uses lead-based paint and that means I have to be extra-careful!

So I purchased a lead-paint rated air-filter and a large box to house the case in while I sanded the paint off.

I started with the inside as there are a lot of little angles and corners and I knew it would be more difficult. I was sure right about it! there are so many little edges and tabs and little pieces it is almost impossible to get it all. 

Here is a good image showing what it looks like after a few hours of work. Note all the little edges and crevices!
results from the first day of sanding

After doing about all I can with the power sander, its time to move to sandpaper. Its tricky as to keep lead-based dust down I am running the shop vac inside the sanding box at the same time as sanding... a lot of work!


Thursday, April 13, 2017

Backboard is complete!

After going through 2 soldering guns and 1 soldering iron I have finished soldering a new ground wire on the backboard for the Harlem Globetrotters Pinball.




It is not as beautiful as I had hoped to make it, but it was quite the learning process.

Next up is cleaning the wiring harness for the head unit. Time to head for the sink in the garage.



Soldering Iron woes

My old 65 watt soldering iron that I had in high school seems to have given up the ghost. It was getting hot only intermittently.

So I purchased a nice big beefy 140 watt soldering gun to finish up my soldering with. With almost double the wattage it should heat up and melt the solder twice as quick!

About 3/4 of the way through soldering the backboard the gun died. Cheap modern crap! So this time I purchased both a new gun and a little soldering iron.

After about 1/.2 hour of soldering, my new gun died.....dammit!

I was looking at the label, examining the manufactures info when I noticed a tiny statement:

It might be hard to read, it says "Duty Cycle: 1 min on, 4 min off"

So basically it is supposed to only be turned on for 1 minute at a time and then must cool down for 4 minutes before it can be used again!

I'm not sure what kind of soldering procedure that would work with, but it sure doesn't fit mine. Fortunately I also purchased a soldering iron. Slow but steady for me from now on.

Thursday, March 30, 2017

Wide Ground Wire woes

This is one of those "Who knew?" type of things.

When I was purchasing parts and equipment for the repair of the Harlem Globetrotter Pinball table, I knew I wanted to replace the groundwire. Although it was not in too bad of shape:


The poorly implemented runs bothered my sense of perfectionism (those wires should be parallel!!) and this seemed like a great time to try out a complete redo.

The old groundwire is a small one, so I purchased a big fat one. After all my Dad always said, no matter what it is, if a little one is good, then a big one is "gooder!"


The problem with wide ground wires is they don't curve very much and while it is possible to do the bed-over turn, its tough to make it look good.

Couple that with my poor soldering skills and you end up with less than beautiful results.

When I started this, I hoped to make something that would look good enough to be in a glass case, where people would ooh and ahh over how beautiful all the behind-the-scenes work was. Now I'm just hoping the lights all light up.

Here are a couple of shots showing the difficulties. Its not bad when the wide ground wire only has to make a couple of bends, but when its a zig-zag pattern it really makes it tough to do a good job!


not quite what I was hoping for in the "beautiful work" department...sigh

Tuesday, March 14, 2017

Light Panel for the Harlem Globetrotters table

Now that the computer table is almost finished - just waiting for another set of lights - I have turned my attention back to pinball.

To recap:

The Harlem Globetrotters table was in serious need of topper work.
The glass was in good condition but:
There were boards missing.
No power was going to the table.
The case had flaking lead-based paint
There were an unknown number of  light bulb problems on the light board.

So to start with, I pulled out the light board (the piece of plywood that all the light bulbs are attached to) and took a look at it.
The board wasn't in too bad of shape, but it seemed like a good warm-up for the full cabinet, so I took pictures of where all the old wires were and pulled them all out as well as the lamp holders the wires were soldered to:



I threw all of the lamp holders into the tumbler:

Although they are not going to win a shinyness contest, they look much better and hopefully will work better without all the corrosion all over them.

The wood panel itself was sanded down (being careful to wear a lead-based paint rated mask,) sealed and repainted in the brightest white I could find.

Now comes the slow work of stapling and soldering the wires and the sockets back into place. I've tried to be a little more careful about 90-degree angles and keeping things parallel where I could, just to make myself happier. 

The work is coming along with about half of the ground wire in place

Tuesday, April 5, 2016

Nightmare with a soldering gun

After 2 hours of work, I am still not finished removing the corroded and burnt parts from the power board on the Harlem Globetrotters table.

 The removal really highlights my lack of skill with a soldering gun and just how hard it is to do a decent job. Especially with the multi-pin connectors.


I started out removing the burnt fuse holders. This wasn't too bad, though the connectors were large and it was hard to unsolder them enough to pull them out.




Then I tried to do the connectors. After several passes with the solder-sucker there was still enough solder to keep them from coming out, so I had to try and heat all of the pins at the same time enough to pry out the connector with a screwdriver.

A complete nightmare. I had to hold the board with one had, hold the soldering gun with the other hand, hold the screwdriver with the third hand and try to pull on the board with the fourth hand.


Trying to unsolder all 8 pins at the same time didn't work, so I tried to unsolder a few and then pull the edge of the board up. Backbreaking work hunched over the board. The solder gun got so hot I couldn't hold it, the board got so hot it burned my fingers.. and after 2 hours of work I am still only partially finished.

Whats even worse is that I am destroying the board in the process.




As you can see from the pictures, it is not a very good looking board. Many of the pads that you are supposed to solder to are gone. My only saving grace is that this is the simplest easiest board there is. Giant traces 3/4 of an inch wide. several pins in a row all connected together.

I may be able to get this board working but it really shows just how hard doing board work really is.